Image via Wikipedia

Utah Inspections on Permanent Foundations Guide for Manufactured Housing are done by Ludlow Engineering and Land Surveying.

Located in Central Utah we are able to access most the the State of Utah for Foundation inspections.  We inspect the foundations of manufactured homes and give our professional opinion of the existing structure.

This process is estimated between $250-$450, depending upon the size and location of the home.  Our real sales point is this – Our firm guarantees that all of our observations and reports will be delivered within 48 hours or our clients receive a 20% discount.  We are that confident in our work and turn around time to accomplish this last minute requirement for house funding.

Call Now at 435.623.0897 for us to inspect your home today.  Again Call 435.623.0897

Sample of Wording found in Engineering Report

November 5, 2009

Dear

It is understood and agreed that this inspection & evaluation by Ludlow Engineering is of readily accessible areas of the building and is limited to visual observation and apparent conditions existing at the time of the inspection.  This report is not intended and should not be considered as a certification and/or guarantee of the work performed.

Based on your request, this inspection was made on November 5, 2009 to check the integrity and status of the structural foundation system.

The manufactured home was rectangular in shape, measuring approximately 27’-0” x 41’-10”.  It is supported along its entire perimeter by an 8” concrete foundation wall.  Looking through the crawl space, the home was supported at the underside by (4) steel I-beams running the length of the building.  Steel Jacks support the I-beams at approximately 5 feet o.c.

During our observation, steel hold-down straps were inspected and appear to have been installed according to minimum standard requirements.  Said Straps are tied to the I-beams and a concrete block.  The footings that supported the jacks appeared to be adequate in size.

During the inspection, it was noted that a covered patio was installed.  The covered patio was constructed with a post and beam system.  The roof has been attached to the existing home.  The covered patio is approximately 8’-5”x 36’-10”.  The tributary width that is supported by the home is 4’-3”.  The rest of the load is transferred to the ground by columns and placed on a footing system under the concrete patio.  I inspected the inside of the home and did not view any stress on the home due to the additional load.  It appears the home is stable.  It is our opinion, that the cover patio has not affected the structural stability of the home.

The residence’s foundation system appears to be in satisfactory condition with no sign of stress and meets minimum building standard requirements, including Permanent Foundations Guide for Manufactured Housing published in September 1996 and Mona City building requirements.

If we can be of any further assistance, please feel free to contact us.

Sincerely,

LUDLOW ENGINEERING

Image via Wikipedia

Ludlow Engineering Provides Elevation Certificates

Below we have listed what an Elevation Certification is all about:

Insurance Continuing Education – Building Elevation Information

BUILDING ELEVATION INFORMATION (SURVEY REQUIRED)

The responsibility of providing a number of elevations based on the building type selected is that of the surveyor, engineer, or architect.  From these elevations gathered, the agent is required to determine the lowest floor for rating flood insurance.

The surveyor, engineer or architect should complete Section C, but if it is left blank, the agent should contact the responsible person who completed the form and the insurance company underwriter with any questions.

Elevations of machinery and equipment servicing the building (water heater, furnace, air conditioner, etc) must be provided, regardless of its location, whether inside or outside of the building, elevated on platform or not elevated.

Where the surveyor, engineer or architect cannot access the crawl space, an estimate on item C2 may be left blank and the estimated measurements entered on the comments section (Section D).

Elevations in Section E are based on feet, except in Puerto Rico, where it is metric and the agent must convert any readings to feet.

SURVEYOR, ENGINEER OR ARCHITECT CERTIFICATION

Section D is the certification of the surveyor, engineer or architect that the information provided by them is correct and their signature and identification number are required—in some states, a seal may be required.

BUILDING ELEVATION INFORMATION, ZONE AO AND ZONE A (WITHOUT BFE)

Section E – The difference between the highest and lowest elevation grade are required.  For the designated Zones, the property owner or his representative may completed Sections A, B & E.

PROPERTY OWNER OR REPRESENTATIVE CERTIFICATION

Address and other contact information about the property owner are requested in Section F.  The party completing Sections A, B, C and E must complete this section also.

COMMUNITY INFORMATION

The local official authorized to administer the community’s floodplain management ordinance may transfer elevation information found on existing documentation—such as from an older elevation certification form or surveyor letterhead—to Section C, and then certify this information by completing Section G.  A statement advising FEMA of this transfer of information must be made in the comment section of the EC.  Section G may also be used to certify Item E4.

insurance continuing education

insurance continuing education online

continuing education insurance

Manufactured Home Hud Foundation Inspection

Article Source: http://EzineArticles.com/?expert=Jon_R_Vandergrift

FHA Modular Home Engineered Reports

What Are They?

A FHA modular home report is completed by a professional engineer who prepares a report based upon his on-site visit of the property.

The report usually required by FHA, gives the opinion of the foundation stability and ties.  This requires the engineer to visit the crawl space of the home and to observe these very things.  This inspection often can be less than ideal, however our engineers are not afraid of getting dirty.

Once the report has been finalized and prepared, the report is furnished to your lending company.

How To Order One?

Simply call today and get your name on the schedule.  Also, most lenders choose to do this themselves.  Either way it is alright with us and we will treat you right.

Call Today (435) 623-0897>>

Salt Lake City – FHA Foundation Inspection

Call Now at 435.623.0897 for us to inspect your home today.  Again Call 435.623.0897

Sample of Wording found in Engineering Report

November 5, 2009

Dear

It is understood and agreed that this inspection & evaluation by Ludlow Engineering is of readily accessible areas of the building and is limited to visual observation and apparent conditions existing at the time of the inspection.  This report is not intended and should not be considered as a certification and/or guarantee of the work performed.

Based on your request, this inspection was made on November 5, 2009 to check the integrity and status of the structural foundation system.

The manufactured home was rectangular in shape, measuring approximately 27’-0” x 41’-10”.  It is supported along its entire perimeter by an 8” concrete foundation wall.  Looking through the crawl space, the home was supported at the underside by (4) steel I-beams running the length of the building.  Steel Jacks support the I-beams at approximately 5 feet o.c.

During our observation, steel hold-down straps were inspected and appear to have been installed according to minimum standard requirements.  Said Straps are tied to the I-beams and a concrete block.  The footings that supported the jacks appeared to be adequate in size.

During the inspection, it was noted that a covered patio was installed.  The covered patio was constructed with a post and beam system.  The roof has been attached to the existing home.  The covered patio is approximately 8’-5”x 36’-10”.  The tributary width that is supported by the home is 4’-3”.  The rest of the load is transferred to the ground by columns and placed on a footing system under the concrete patio.  I inspected the inside of the home and did not view any stress on the home due to the additional load.  It appears the home is stable.  It is our opinion, that the cover patio has not affected the structural stability of the home.

The residence’s foundation system appears to be in satisfactory condition with no sign of stress and meets minimum building standard requirements, including Permanent Foundations Guide for Manufactured Housing published in September 1996 and Mona City building requirements.

If we can be of any further assistance, please feel free to contact us.

Sincerely,

LUDLOW ENGINEERING

Located in Central Utah we are able to access most the the State of Utah for Foundation inspections.  We inspect the foundations of manufactured homes and give our professional opinion of the existing structure.

This process is estimated between $250-$450, depending upon the size and location of the home.   We are that confident in our work and turn around time to accomplish this last minute requirement for house funding.

Call Now at 435.623.0897 for us to inspect your home today.  Again Call 435.623.0897

Sample of Wording found in Engineering Report

for Manufactured Home Foundations.

November 5, 2009

Dear

It is understood and agreed that this inspection & evaluation by Ludlow Engineering is of readily accessible areas of the building and is limited to visual observation and apparent conditions existing at the time of the inspection.  This report is not intended and should not be considered as a certification and/or guarantee of the work performed.

Based on your request, this inspection was made on November 5, 2009 to check the integrity and status of the structural foundation system.

The manufactured home was rectangular in shape, measuring approximately 27’-0” x 41’-10”.  It is supported along its entire perimeter by an 8” concrete foundation wall.  Looking through the crawl space, the home was supported at the underside by (4) steel I-beams running the length of the building.  Steel Jacks support the I-beams at approximately 5 feet o.c.

During our observation, steel hold-down straps were inspected and appear to have been installed according to minimum standard requirements.  Said Straps are tied to the I-beams and a concrete block.  The footings that supported the jacks appeared to be adequate in size.

During the inspection, it was noted that a covered patio was installed.  The covered patio was constructed with a post and beam system.  The roof has been attached to the existing home.  The covered patio is approximately 8’-5”x 36’-10”.  The tributary width that is supported by the home is 4’-3”.  The rest of the load is transferred to the ground by columns and placed on a footing system under the concrete patio.  I inspected the inside of the home and did not view any stress on the home due to the additional load.  It appears the home is stable.  It is our opinion, that the cover patio has not affected the structural stability of the home.

The residence’s foundation system appears to be in satisfactory condition with no sign of stress and meets minimum building standard requirements, including Permanent Foundations Guide for Manufactured Housing published in September 1996 and Mona City building requirements.

If we can be of any further assistance, please feel free to contact us.

Sincerely,

LUDLOW ENGINEERING

Utah Inspections on Permanent Foundations Guide for Manufactured Housing are done by Ludlow Engineering and Land Surveying.

Located in Central Utah we are able to access most the the State of Utah for Foundation inspections.  We inspect the foundations of manufactured homes and give our professional opinion of the existing structure.

This process is estimated between $250-$450, depending upon the size and location of the home.  Our real sales point is this – Our firm guarantees that all of our observations and reports will be delivered within 48 hours or our clients receive a 20% discount.  We are that confident in our work and turn around time to accomplish this last minute requirement for house funding.

Call Now at 435.623.0897 for us to inspect your home today.  Again Call 435.623.0897

Sample of Wording found in Engineering Report

November 5, 2009

Dear

It is understood and agreed that this inspection & evaluation by Ludlow Engineering is of readily accessible areas of the building and is limited to visual observation and apparent conditions existing at the time of the inspection.  This report is not intended and should not be considered as a certification and/or guarantee of the work performed.

Based on your request, this inspection was made on November 5, 2009 to check the integrity and status of the structural foundation system.

The manufactured home was rectangular in shape, measuring approximately 27’-0” x 41’-10”.  It is supported along its entire perimeter by an 8” concrete foundation wall.  Looking through the crawl space, the home was supported at the underside by (4) steel I-beams running the length of the building.  Steel Jacks support the I-beams at approximately 5 feet o.c.

During our observation, steel hold-down straps were inspected and appear to have been installed according to minimum standard requirements.  Said Straps are tied to the I-beams and a concrete block.  The footings that supported the jacks appeared to be adequate in size.

During the inspection, it was noted that a covered patio was installed.  The covered patio was constructed with a post and beam system.  The roof has been attached to the existing home.  The covered patio is approximately 8’-5”x 36’-10”.  The tributary width that is supported by the home is 4’-3”.  The rest of the load is transferred to the ground by columns and placed on a footing system under the concrete patio.  I inspected the inside of the home and did not view any stress on the home due to the additional load.  It appears the home is stable.  It is our opinion, that the cover patio has not affected the structural stability of the home.

The residence’s foundation system appears to be in satisfactory condition with no sign of stress and meets minimum building standard requirements, including Permanent Foundations Guide for Manufactured Housing published in September 1996 and Mona City building requirements.

If we can be of any further assistance, please feel free to contact us.

Sincerely,

LUDLOW ENGINEERING